The leading plant in the production of sanitary engineering

+38 048 734 47 57 To get a consultation

Продукція / Sectional radiators / SAN TEH RAI – aluminum radiators

SAN TEH RAI – aluminum radiators

15 year warranty

Aluminum heat radiators “SAN TEH RAI” are widely used with any heating systems.

Heat radiator is produced on advanced equipment from specially prepared aluminum alloy meeting quality standards ENAB46100, this allows ensuring comfortable exploitation for not less than 50 years. Aluminum heat radiators SAN TEH RAI are represented by a model with an axle spacing of 500 mm.

15 year warranty

Calculate wholesale price

Advantages aluminum radiators SAN TEH RAI

Unique system of side lobes allows hastening convection and improve efficiency of the device

High heating capacity

Fit for installing in usual as well as low-temperature systems with any type of boiler modules including with condensation boilers

Effective protection from pressure hammers

Structural solidity allows exploitation of heat radiator in conditions of high pressure and non-prepared heat carrying agent

Coloring of a thermal radiator by anaphoresis method according to German technologies.

Quality certificates and technical documentation

Manufacturer's warranty for the San TEH RAI aluminum radiator is 15 years; (subject to compliance with the standards and conditions of installation and operation described in the product data sheet)

SAN TEH RAI 500

Specifications

Axle spacing L, mm

500

Depth of section В, mm

Width of section С, mm

Height of section А, mm

575

Volume of heat carrying agent, l

0,42

Heat output of one section Δt=70°C, W

172

Heat output of one section Δt=60°C, W

130

Heat output of one section Δt=50°C, W

110

Max temperature of heat carrying agent, °С

120

Max operating pressure, Bar

Testing pressure, Bar

The value of the hydrogen index, pH

6,5-9,0

Installation and operating recommendations

Installation of radiators should only be carried out: + ×
- If there is a heat engineering project created by a licensed design organization and certified by the organization responsible for the operation of the heating system of the room in which this radiator is planned to be installed;
- Вy a specialized installation organization; in accordance with building codes and regulations.
- After the radiator has reached room temperature naturally, without direct exposure to heating devices.
  With the mandatory possibility of cutting off the inlet and outlet of the coolant with special fittings.
- Recommended installation and operating conditions:
- For optimal heat transfer of radiators, the distance between the radiator and the floor should be 70-120mm, and between the radiator and the window sill at least 80mm. The brackets must provide a distance of 30-50mm from the wall, as well as a horizontal position of the radiator.
- Immediately before installing the plugs and adapters, lubricate the gasket with a heat-resistant (up to 135° C) silicone sealant.
- It is recommended to install the radiator to the pipelines without removing the protective plastic film, which will protect the appearance of your radiator.
- In the case of a one-way side connection of a radiator with a number of sections more than 12, it is recommended to install a flow guide with a length ≈ ≈ of the radiator length in the intake manifold.
- It is not recommended to reconfigure radiators in order to reduce or increase the number of sections, as well as replace individual sections of the radiator. Warranty obligations do not apply to refurbished radiators.
- During Operation, it is necessary to periodically remove air from the Upper Collector using an air outlet valve.
- It is not recommended to open the radiator valves abruptly to avoid hydraulic shock.
- The radiator must be filled with coolant during the entire period of operation in accordance with clause 1.3 of this passport according to GOST 31311-2005, EN 442.
- Transportation and storage of radiators should be carried out in accordance with GOST 31311-2005, EN 442.
- Number of sections in radiators that are mass-produced: from 4 to 12.
- During transportation, the twisted nipple inside the radiator may be slightly loosened, so before installing the radiator in the heating system, it is necessary to tighten the nipples connecting the sections to each other.